The short answer
The Canon AE-1 takes one 6-volt battery in the 4LR44 / PX28 size. That’s a small cylinder about 13mm across and 25mm long. Any of these will work:
| Chemistry | Common names on the pack | Notes |
|---|---|---|
| Alkaline | 4LR44, A544, PX28A, 28A | Cheapest and sold almost everywhere. Voltage sags gradually as it runs down. |
| Silver oxide | 4SR44, PX28, PX28S | Holds its voltage steadier until near the end. Usually costs a little more. |
| Lithium | PX28L, 2CR1/3N, L544 | 6V lithium cell with very low self-discharge. A good choice for a spare. |
All three share the same size. The AE-1 Program takes the same cell: its manual lists 4LR44/A544, 4SR44/PX28 and PX28L. The A-1 takes it too: its manual lists the same 6V silver-oxide (PX28, Eveready 544) and alkaline types, and Canon’s museum page gives 4LR44. The AV-1 uses it as well: Canon’s museum page lists a 6V 4G-13 mercury cell or a 4LR44.
Why the battery matters more on an AE-1
Many old SLRs only need a battery for the light meter. The AE-1 is different: it doesn’t work at all without a battery. The shutter is timed electronically, so with a dead cell the shutter won’t fire at any speed, and the meter won’t work either.
That has two practical effects:
- A “broken” AE-1 often just has a flat or badly seated battery. Before you send one for repair or pass on a listing, try a fresh cell and clean the contacts.
- Carry a spare. When the cell dies mid-roll, the camera stops. Lithium PX28L cells keep well in a bag.
Where the battery goes and how to change it
The battery compartment is on the front of the camera, beside the lens mount, under a small plastic door. Camera-wiki notes the door can be opened with the edge of the hot-shoe cover.
- Open the door.
- Remove the old cell, noting which way it faces.
- Check the contacts. If they’re dull or crusty, clean them gently. See below.
- Fit the new cell the right way round. The polarity is marked inside the compartment.
- Close the door until it sits flush.
Be gentle with the door. It’s plastic, it breaks often, and owners report that cheap aftermarket replacements fit poorly. If the door won’t stay shut, the battery can lose contact and the camera will act dead.
How to check the battery
There’s a battery check button on the top plate, to the left of the prism. Press it while looking through the finder and watch the meter needle. The manual says the battery is fine if the needle rests on or below the index mark opposite f/5.6. A fresh cell swings it down near f/2.8. If the needle sits above the index, or doesn’t settle within about three seconds, the cell is nearly done. If the needle barely moves or the shutter won’t fire, replace the cell.
Does alkaline vs silver oxide change the meter?
This is a common worry carried over from cameras whose meters were designed for mercury cells. Canon’s own manual lists both a 6V silver-oxide cell and a 6V alkaline cell as correct for the AE-1, so the camera was designed to take either. One owner on r/AnalogCommunity also tested the meter at a range of supply voltages. He got the same f-stop readings from 3.6V up to 7V. The readings only changed below about 3.4V, and by then the battery check already showed the cell as dead and the shutter wouldn’t release.
In practice, any of the three chemistries is fine. Silver oxide or lithium may simply last longer before the camera quits.
Can I use four LR44 button cells instead?
Owners do stack four LR44 or SR44 button cells in a pinch. Four 1.5V cells give the same 6V. Four LR44s stacked are about 21.6mm long against roughly 25mm for a 4LR44 (each LR44 is 5.4mm thick), so the stack needs a spacer or adapter to make contact. A proper 4LR44 or PX28 is the cleaner fix.
Corrosion and storage
If a cell was left in the camera for years, it may have leaked. Look for green or white crust on the contacts.
- Light corrosion can usually be cleaned off. iFixit’s AE-1 guide covers cleaning corroded terminals.
- Heavy corrosion, or a camera that drains a fresh cell within a day, can mean corrosion between the battery contact and the body. That’s a repair job.
If you’re putting the camera away for months, take the battery out. A leaking cell is one of the most common ways a working AE-1 gets damaged.
Troubleshooting: the AE-1 still won’t fire with a new battery
Work through these in order:
- Check the cell is the right way round and fully seated, with the door closed.
- Clean the contacts, both on the door and in the chamber.
- Make sure the film is advanced fully. A half-stroke won’t cock the shutter.
- Check the shutter lock lever. The lever beside the shutter button can lock the release.
- If it still won’t fire, the problem may be dirt on the shutter-release magnet under the bottom plate. That’s a common AE-1 fault, and usually a quick repair. See the Canon AE-1 page for other known issues.
FAQ
What battery does the Canon AE-1 take? One 6V cell: 4LR44 or PX28A (alkaline), 4SR44 or PX28S (silver oxide), or PX28L (lithium). They’re all the same size.
Is the 4LR44 the same as the PX28? They’re the same size and nominal 6V. The suffix tells you the chemistry: 4LR44 and PX28A are alkaline, 4SR44 and PX28S are silver oxide, and PX28L is lithium. All work in the AE-1.
Will the Canon AE-1 work without a battery? No. The shutter is electronically timed, so nothing fires without one.
How long does an AE-1 battery last? It depends on use and chemistry, and we haven’t found a reliable published figure. Carry a spare either way.
Where is the battery on a Canon AE-1? Behind the small door on the front of the body, beside the lens mount.
Can I use a lithium battery in the AE-1? Yes. A 6V PX28L / 2CR1/3N is the same size and voltage.