The short answer
The “Canon squeal” is a squeak or chirp when you fire a Canon AE-1, AE-1 Program or A-1. It comes from the mechanism that slows the mirror on its way back down, when its lubricant dries out. It’s common on all of Canon’s A-series bodies.
- Does it ruin photos? Not at first. But it can slow the mirror and add shutter lag, and camera-wiki warns that left alone it can eventually cause damage that can’t be repaired.
- The fix: a tiny drop of light oil in the right spot. Owners do it themselves with a syringe; iFixit rates it moderate and 15–30 minutes. A full clean, lube and adjust (CLA) is the thorough fix.
- Buying used? Treat a squeal as a reason to pay less, not to walk away.
What causes it
Owners and repairers agree on the area, but not the exact part:
- A Photrio poster who says he repaired A-series bodies for Canon Australia blames dry bearings on the mirror governor, the original lubricant drying out over several years. He says it can start in as little as 4 or 5 years, depending on climate and storage.
- Others describe it as a dry bearing on the flywheel of the mirror braking mechanism, or the gear train for the mirror return on the side of the mirror box.
- Another Photrio poster calls it the mirror damper.
- A minority says it isn’t dried lubricant at all, but a worn pin or bushing. The ex-Canon repairer disagrees, saying the plastic parts don’t wear out.
Camera-wiki describes it as the mirror brake’s lubricant drying out on the A-series.
Which cameras get it
Photrio posters say the squeak is found in all the Canon A-series bodies, and name the A-1, AE-1 and AE-1 Program. The ex-Canon repairer says it doesn’t occur on the F series, and the T series didn’t develop it.
How to recognize it
Fire the shutter a few times. Instead of a clean clack, you hear a squeak or chirp. One owner hears it as the shutter closes. Listen at several speeds, including 1/60s and slower.
A Photrio poster adds that the whole shutter cycle can sound slower. It’s the mirror movement slowing, not the shutter itself, which gives you shutter lag.
Does it matter?
| View | Source |
|---|---|
| “The squeak isn’t necessarily a problem,” but it means the body is due for a CLA | Photrio poster |
| It can delay the shutter, causing lag | Photrio poster |
| Left alone, it can lead to damage that can’t be repaired | Camera-wiki |
Our take: fix it soon. The repair is cheap, and spare parts are scarce; the ex-Canon repairer says there are really no new spare parts available.
The DIY fix
iFixit’s guide is written for the AE-1 Program, though its intro says AE-1. It doesn’t need full disassembly.
You need: Phillips #0 and #00 screwdrivers, a syringe with a blunt needle, and a very small amount of light oil.
- Remove the battery before oiling, as one Photrio poster advises.
- Take off the front cover plate (the “beauty piece”) around the lens mount.
- Remove the top-left screw on the lens mount.
- Put a tiny drop of oil into that screw hole with the syringe. An iFixit commenter says the gear sits slightly below the upper wind-side lens mount screw hole, and suggests a slightly bent needle to feel for it.
- Refit the battery and test. The shutter is electronic, so it needs power. iFixit’s author describes a clean “CLICK, CLICK” when it’s fixed.
- Refit the screw and front plate.
An iFixit commenter adds oil in small steps, firing the shutter at least three times between drops. Another Photrio method for the AE-1 Program goes in through the bottom plate instead.
Non-Program AE-1: one iFixit commenter says the gear isn’t reachable the same way on the plain AE-1, and their camera wouldn’t fire after reassembly. If you have an AE-1, a technician may be the safer route.
Which oil to use
This is where owners disagree most:
| Oil | Verdict |
|---|---|
| Clock or watch oil, clear and as thin as water | Recommended by Photrio posters |
| Very light mineral oil | Recommended by an iFixit commenter |
| Vegetable or other food oil | iFixit’s author used it; a commenter strongly discourages it, because food oils spoil and may jam the mechanism |
| Lithium grease | Too thick for the shutter gears, per an iFixit commenter; it slows the shutter and stiffens in the cold |
| WD-40 or 3-in-1 | A Photrio poster says no |
Warnings
- Too much oil is worse than none. iFixit commenters warn it can leak into the mirror box and onto the shutter curtains, focusing screen or electronics. Use the smallest drop you can.
- Don’t spray aerosol lubricants into the camera, per an iFixit commenter.
- It can come back. One Photrio owner’s camera worked for about three rolls after two services before squeaking again.
- Avoid heat. A repairer told one Photrio owner not to let the camera get too hot after the repair.
When to get a CLA instead
The ex-Canon repairer says the only correct service is to take the mirror box out, about 2.5 hours on an A-1 or AE-1 and 1.5 hours on an AE-1 Program. He says many technicians get it done in under an hour by oiling through the front or top. Choose a CLA if the camera has other faults, if it’s a plain AE-1, or if you don’t want to risk oil on the shutter.
FAQ
Why does my Canon AE-1 squeak when I take a picture? The lubricant in the mirror’s braking mechanism has dried out. It’s common on all Canon A-series cameras.
Is the Canon squeal bad? It doesn’t ruin pictures at first, but it can cause shutter lag and, left long enough, damage. Fix it soon.
How do I fix the Canon AE-1 squeak? A tiny drop of clock oil or light mineral oil on the mirror mechanism gear, through the top-left lens mount screw hole, per iFixit. Or pay for a CLA.
Does the AE-1 Program squeak too? Yes. So does the A-1. It’s an A-series trait.
Can I use WD-40 on my camera? No. Photrio posters recommend clock or watch oil instead.