The short answer
The Minolta SRT 101 takes one 1.35V PX625 mercury cell in the chamber on the base. Mercury cells are no longer sold. The good news: the battery runs only the light meter. The shutter, film advance and every speed work without it.
Your options:
| Option | Voltage | Notes |
|---|---|---|
| MR-9 adapter + SR43 (386) silver-oxide cell | About 1.35V | The most stable choice. The adapter costs far more than the cell. |
| 675 zinc-air hearing-aid cell in an adapter ring, or a Wein MRB625 | 1.35–1.4V | Close to the right voltage and cheap, but zinc-air cells dry out within weeks to months once opened. |
| 1.5V 625A alkaline | 1.5V | Drops straight in and is sold for this camera, but the meter was calibrated for 1.35V. |
| No battery | — | Everything but the meter works. Use a handheld meter, phone app or sunny 16. |
Does 1.5V throw the SRT 101’s meter off?
Yes, somewhat. Ausgeknipst lists the SRT among cameras whose meters have no bridge circuit to compensate for voltage, so the reading changes with the battery. Owners on r/AnalogCommunity say a 1.5V alkaline tends to make the SRT underexpose.
Bruce Varner tested all three types of cell in two SRT 101s against a Sekonic meter. The two cameras agreed more closely the nearer the cell was to 1.35V, but he found all three usable if you shoot a test roll and adjust the ASA dial to match.
Our take: with color negative film, a 625A plus a quick check against a phone meter is fine. For slide film, use an MR-9 adapter or a 1.35V zinc-air cell.
Beware fake MR-9 adapters
A real MR-9 adapter has a small circuit that drops a silver-oxide cell’s 1.55V to about 1.35V, as 35mmc describes. PHSNE warns that cheap look-alikes are often plain brass holders with no electronics, which give you the full 1.55V. If the price looks too good, it probably is.
How to check the battery
Set the switch on the base to BC (battery check). If the needle in the finder sits over the small rectangle, the cell is good. Then turn the switch back. Don’t leave it on BC: the manual warns this drains the cell within hours. Turn it to OFF when you put the camera away.
How to calibrate with a substitute cell
- Fit the new cell and run the battery check.
- Point the SRT and a phone meter app at the same scene, in sun, shade and indoors.
- If the SRT is off by the same amount each time, change the ASA dial to compensate. Varner’s tests suggest this works with all three cell types.
- If the error changes with the light, switch to a 1.35V option.
Our mercury battery replacement guide explains each substitute in more detail.
Which cameras take the same battery
The PX625 also powers the meters of the Olympus OM-1, Canonet QL17 G-III, Canon FTb, Olympus 35 RC and Minolta Hi-Matic 7s. The same options work in all of them.
FAQ
What battery does the Minolta SRT 101 take? One 1.35V PX625 mercury cell originally. Use an MR-9 adapter with an SR43 cell, a 675 or Wein zinc-air cell, or a 1.5V 625A alkaline with a meter check.
Does the SRT 101 work without a battery? Yes. Only the light meter needs power. Every shutter speed works.
Can I use a 625A alkaline in the SRT 101? Yes, it fits. Owners report it tends to underexpose; check against another meter and adjust the ASA dial.
How do I test the SRT 101 battery? Set the base switch to BC. The needle should sit over the small rectangle in the finder.
Can I use an LR44 in the SRT 101? Not as a drop-in. The camera is built for a PX625; use one of the options above.