Skip to content
lastroll

Guide

Mercury Battery Replacement for Film Cameras: PX625, PX675 and PX400 Options Compared

Your camera wants a banned 1.35V mercury cell. Wein zinc-air, 675 hearing-aid cells, MR-9 adapters, diodes and 1.5V cells compared for meter accuracy.

Reviewed Nov 21, 20265 min read

The short answer

Many cameras from the 1960s and 1970s were built for a 1.35V mercury cell, usually the PX625 (also sold as PX13 or MR-9). Mercury cells were banned, and today’s same-size cells run at 1.5V or 1.55V, which can throw the camera’s meter off.

Your best options, in order:

  1. Wein MRB625 zinc-air cell (1.35V). Right voltage, drops straight in. Lasts a couple of months once activated.
  2. 675 hearing-aid cell (about 1.4V) in an adapter or with an O-ring. Close enough for most cameras and very cheap.
  3. A genuine MR-9 adapter with a silver-oxide cell. It drops the voltage to 1.35V electronically. Costs about $40 once, then cells are cheap.
  4. A 1.5V cell with an ISO correction, after testing the meter against a known-good one.

First, check whether you need a battery at all. On many of these cameras the battery runs only the meter. The Olympus OM-1, Canon FTb, Minolta SRT 101 and Pentax Spotmatic all fire at every speed with no battery. You can meter with a phone app and skip the problem entirely.

Why mercury cells disappeared

Jason Schneider’s guide on Rangefinder Forum cites the US Mercury-Containing and Rechargeable Battery Management Act of 1996, which ended mercury in consumer batteries because of its toxicity. PHSNE says manufacturing simply stopped. Have Camera Will Travel gives the same 1996 date for the US ban.

Why the voltage matters

A mercury cell held a steady 1.35V for almost its whole life, and camera makers calibrated meters to it. The replacements differ:

Cell type Voltage Behavior
Mercury (original) 1.35V Flat until empty
Zinc-air (Wein, hearing-aid) 1.35–1.4V Flat, but runs down once exposed to air
Silver oxide About 1.55V Flat until near the end
Alkaline 1.5V when new Falls steadily as it’s used

Schneider says the wrong voltage can put readings off by as much as 2–3 stops. PHSNE adds that the error isn’t linear, so a single ISO offset may be right in bright light and wrong in dim light. Some older meter designs are less fussy: Schneider says Spotmatics before the Spotmatic F had circuits indifferent to voltage.

The options in detail

Wein MRB625 zinc-air (1.35V)

  • What it is: a zinc-air cell made to the PX625 size and voltage. Schneider says it replaces the PX625, PX13, PX67 and MR-9.
  • Fit: PHSNE says no spacer is needed. Ken Rockwell notes a washer around it for a snug fit.
  • Voltage: Rockwell measured one rising to 1.35V within about 13 minutes of activation and holding about 1.4V for many months.
  • Life: PHSNE says a couple of months to perhaps six once the tab is off. Unactivated, Schneider says they keep up to 10 years.
  • Cost: Rockwell paid $8 each in 2026.
  • Catch: once activated it runs down whether you use the camera or not. Some owners report much shorter life in certain cameras.

675 hearing-aid cell (about 1.4V)

  • What it is: the same zinc-air chemistry, sold cheaply in packs for hearing aids.
  • Fit: it’s smaller than a 625. Ausgeknipst uses an 11 × 15 × 2mm O-ring. A 35mmc writer wraps the edge with blu-tak, keeping it off the flat + face. Adapters are sold too.
  • Life: 2–3 months per ausgeknipst; a couple of weeks to a couple of months per PHSNE.
  • Catch: a loose fit can lose contact, especially in cameras that touch the cell on its side.

The 35mmc writer found their Olympus 35 RC metered well on a 675.

MR-9 adapter (silver oxide, voltage reduced)

  • What it is: a 625-size holder with a small circuit that drops a silver-oxide cell’s 1.55V to 1.35V. 35mmc and Schneider both describe built-in electronics.
  • Cell: usually a 386 / SR43 silver-oxide cell. Schneider says some take an SR44 or 357.
  • Cost: about $40 from C.R.I.S. in the US, per PHSNE and Schneider; a Japanese version is made by Kanto.
  • Catch: cheap look-alikes on marketplaces are often plain brass holders with no electronics. PHSNE and Outside the Shot both warn about these. A plain holder gives you a silver-oxide cell at full 1.55V.

Diode fitted by a repairer

A technician can wire a diode into the battery circuit to drop the voltage, so the camera runs on modern silver-oxide cells for good. Schneider lists typical drops: about 0.25V for a Schottky diode, 0.3–0.35V for a germanium diode. He quotes $50–$60 plus shipping. PHSNE calls it the most expensive route and notes it won’t suit every camera. Outside the Shot describes the procedure on the OM-1.

1.5V alkaline or silver oxide with correction

A 625A alkaline fits and is easy to find. Schneider says a consistent error can be offset by setting a lower ISO, but only after checking the meter at several light levels. Ausgeknipst advises against alkaline, because its voltage sags and the error keeps changing.

Other mercury sizes

Original Used in (examples) Options
PX625 / PX13 / MR-9 Olympus OM-1, Canon FTb, Canon F-1, Minolta SRT 101, Hi-Matic 7s, Olympus 35 RC, Canonet QL17, Yashica Mat-124G, Spotmatic F Everything above
PX675 Konica C35 Wein MRB675, or a 675 hearing-aid cell (the same size)
PX400 Pentax Spotmatic SP and SP II Wein MRB400 (1.35V)

The camera lists come from PHSNE, ausgeknipst and Schneider. Each camera’s own page covers its quirks in more detail.

Not mercury, but often confused: the Yashica Electro 35 used a 5.6V mercury pack, which has its own modern replacements. Cameras that take SR44 or LR44 cells never used mercury; see LR44 vs SR44 vs 357.

How to check you got it right

  1. Fit the new cell and run the camera’s battery check.
  2. Point the camera and a phone meter app (or another camera you trust) at the same scene.
  3. Repeat outdoors in sun, in shade and indoors.
  4. If the camera reads the same in all three, you’re done. If it’s off by the same amount each time, set an ISO offset. If the error changes with the light, use a voltage-matched cell or adapter instead.

FAQ

What can I use instead of a PX625 mercury battery? A 1.35V Wein MRB625 zinc-air cell, a 675 hearing-aid cell in an adapter, or an MR-9 adapter with a silver-oxide cell.

Can I use a 1.5V battery in a camera designed for 1.35V? It fits, but the meter may read wrong, sometimes by 2–3 stops. Test against another meter and correct with ISO if the error is consistent.

How long does a zinc-air battery last in a camera? Usually a few weeks to a few months once activated, whether you use the camera or not.

Are cheap MR-9 adapters worth buying? Usually not. Many are plain holders with no voltage reduction. Buy one that states it contains a voltage-reducing circuit.

Do I need a battery at all? Not on cameras with mechanical shutters, like the OM-1 or Canon FTb. The battery only runs the meter.

Cameras in this guide

Sources

  1. Mercury camera battery issues and solutions — PHSNE
  2. Solving the mercury battery dilemma: a quick guide (Jason Schneider) — Rangefinder Forum
  3. PX625 battery alternatives — ausgeknipst
  4. Wein EPX-625 (MRB625) — Ken Rockwell
  5. MR-9 battery adapter — 35mmc
  6. How to adapt a 675 hearing-aid battery as a PX625 replacement — 35mmc
  7. Olympus OM-1 Mercury Battery Replacements — Outside the Shot
  8. Which Battery Does Your Minolta Camera Take? — Have Camera Will Travel

Last reviewed Nov 21, 2026.