Skip to content
lastroll

Battery · 5.6V (original); replacements 6–6.4V off load

Yashica Electro 35 Battery: PX32 Replacements, Adapters and the Battery Check Lamp

The Yashica Electro 35 took a 5.6V PX32 mercury cell. New PX32A and PX32S cells, 4LR44 and 4SR44 in an adapter, lithium, and why the check lamp may stay dark.

Reviewed Nov 21, 20263 min read

The short answer

The Yashica Electro 35 was designed for one 5.6V PX32 mercury battery, sold as the Mallory TR164, Eveready E164 or Varta V164PX. Mercury cells are no longer made. Ausgeknipst describes the PX32 as four 1.35V mercury cells in one long can, about 45mm long.

Today you have two good options:

  1. A new-production PX32A (alkaline) or PX32S (silver oxide). Contax 139 Resource reports these are made again by a UK manufacturer. They’re the original size, so no adapter is needed.
  2. A 6V stack (4SR44 or 4LR44) in a PX32 adapter. The 6V cells are only about 25mm long, so ausgeknipst sells an adapter that brings them to the PX32’s length.

The battery runs the meter, the auto exposure and the timed speeds. Our Electro 35 page explains that without a battery the shutter fires only at 1/500s.

Does 6V instead of 5.6V matter?

Not for exposure. Ausgeknipst explains that the Electro’s meter is a bridge circuit, which compensates for voltage changes over a wide range. Feuerbacher reports the camera works properly anywhere between about 4.6V and 6.5V. Contax 139 Resource went further: with the light sensor replaced by a fixed resistor, test exposures came out the same at 6V, 4V and 3.5V.

Why the battery check lamp may stay dark

This is the part that confuses owners. The battery check lamp doesn’t just need voltage at rest; it needs voltage under load. Contax 139 Resource quotes the service manual: the lamp turns on at 3.9V, and the camera draws 60–70mA with a lamp lit.

Their measurements, off load and with the check button pressed:

Battery Off load Under load (check pressed) Above the 3.9V lamp threshold?
PX28A / 4LR44 alkaline 6.0V 3.7V No; the lamp didn’t light
4SR44 silver oxide 6.4V 4.4V Yes
2CR1/3N lithium 5.8V 4.6V Yes; the lamp lit and the warning lamps were brighter
A32PX (PX32A) alkaline 5.8V 5.5V Yes, by the widest margin

So a fresh 4LR44 can fail the battery check while still giving correct exposures. Contax 139 Resource found the camera exposed properly with it, but the over and under lamps in the finder were much dimmer. Some users report the check lamp working briefly with a 4LR44 and then stopping.

The takeaway: if your check lamp stays dark with a 4LR44, try a PX32A, 4SR44 or lithium before you assume the camera is faulty.

Which should you buy?

Option Pros Cons
PX32A / PX32S Original size, no adapter, held 5.5V under load in testing Harder to find, costs more
4SR44 in an adapter Stayed above the lamp threshold in testing Needs an adapter
2CR1/3N lithium Strong under load, bright warning lamps Needs a spacer
4LR44 / PX28A in an adapter Cheapest and easiest to find May not light the check lamp; dim warning lamps
Four loose LR44 / SR44 Works in a pinch Ausgeknipst calls it fiddly; Feuerbacher made a cardboard-and-foil adapter

Our pick is a PX32A if you can get one, or a 4SR44 in an adapter if you can’t.

How to check the battery

Press the small battery check button on the back. Our Electro 35 page describes the green lamp lighting with a good cell. If it stays dark, see the section above before you suspect the camera.

Which cameras take the same battery

Ausgeknipst lists the PX32 for the whole family, including the original Electro 35, G, GS, GSN, GT, GTN, GL and Professional, the Electro AX SLR, and Kyocera-branded versions. Feuerbacher notes the GTN is the black version of the GSN.

FAQ

What battery does the Yashica Electro 35 take? Originally a 5.6V PX32 mercury cell. Use a new PX32A or PX32S, or a 4SR44 / 4LR44 in a PX32 adapter.

Can I use a 4LR44 in a Yashica Electro 35? Yes, in an adapter. Exposure is fine, but the battery check lamp may not light because the voltage sags under load.

Does 6V damage the Electro 35? No source we found reports damage. Feuerbacher says the camera works properly from about 4.6V to 6.5V.

Why won’t the battery check light come on with a new battery? Probably the battery sags below the lamp’s 3.9V threshold under load. Try a PX32A, 4SR44 or lithium cell.

Does the Yashica Electro 35 work without a battery? Only at 1/500s. Auto exposure and the slower speeds need power.

Cameras that use it

Sources

  1. Replacement battery for Yashica Electro 35 series — Contax 139 Resource
  2. Which battery replaces the PX32? — ausgeknipst
  3. Yashica Electro 35 GSN — M. Feuerbacher
  4. Yashica Electro 35 instruction manual — Butkus.org
  5. Yashica Electro 35 — Wikipedia

Last reviewed Nov 21, 2026.